SLP-231 The SLP-231 is a 2U high 19" rack mount 220 Volt 30 amp single phase power distribution bar. This model has a NEMA L14-30 for a Main Inlet connector with a paralleled Outlet (pass through) connector for daisy connectivity of racks. There are two 20 Amp electrical circuit breakers on the front panel, each of which are connected to one of the two ( X & Y ) phases of the main power inlet connector. Each circuit breaker is connected to a pair of T-slot U-ground duplex receptacle outlets located on the rear panel.
|
|
|
SLP-232 The SLP-232 is a 2U high 19" rack mount 220 Volt 30 amp single phase power distribution bar. This model has a NEMA L14-30 for a Main Inlet connector. There are two 20 Amp electrical circuits connected to each of the two ( X & Y ) phases of the main power inlet connector. Each of the four circuit breakers supply a T-slot Uground duplex receptacle located on the rear panel. Two of the four independent circuit breakers distribute power from each phase of the inlet connector to each half of the split T-slot duplex convenience outlet on the front panel.
|
|
|
| SLP-2323 |
|
|
SLP-234 The SLP-234 is a 2U high 19" rack mount 220 Volt 30 amp single phase power distribution bar. This model has a NEMA L14-30 for a Main Inlet connector. There are two 20 Amp electrical circuit breakers on the front panel each of which are connected to one of the two ( X & Y ) phases of the main power inlet connector. Each breaker independently distributes power to a T-slot duplex U-ground receptacle on the rear panel which is also parallel connected to one half of the split T-slot duplex U-ground convenience receptacle located on the front panel.
|
|
|
SLP-235 The SLP-235 is a 2U high 19" rack mount 220 Volt 30 amp single phase power distribution bar. This model has a NEMA L14-30 for a Main Inlet connector. There are four 20 Amp electrical circuit breakers on the front panel, two of these breakers are connected to the ‘X’ phase and two to the ‘Y’ phase of the main power inlet connector. Each breaker independently distributes power to each half of a pair of split T-slot duplex U-ground receptacle for a total of four independent circuits or outlets on the rear panel.
|
|
|
SLP-237 The SLP-237 is a 2U high 19" rack mount 220 Volt 30 amp single phase power distribution bar. This model has a NEMA L14-30 for a Main Inlet connector. There are two double 15 amp breakers and two single 20 Amp breakers located on the front panel. Both of the double 15 Amp breakers independently supply power to duplex twist-lock outlets located on the rear panel. Each of the remaining two 20 Amp single breakers are connected to one of the two ( X & Y ) phases of the main power inlet connector and distribute power to T-slot duplex U-ground receptacles located on the rear panel.
|
|
|
SLP-238 The SLP-238 is a 2U high 19" rack mount 220 Volt 30 amp single phase power distribution bar. This model has a NEMA L14-30 for a Main Inlet connector. There are six independent 20 amp breakers located on the front panel. Each of the X1, X2, Y1 & Y2 breakers distribute power to four T-slot duplex U-ground receptacles located on the rear panel. The remaining X3 & Y3 breakers distribute power to a split T-slot duplex U-ground convenience receptacle located on the front panel.
|
|
|
SLP-335 The SLP-335 is a 2U high 19" rack mount (220 Volt 30 amp 3Ø) power distribution bar. This model has a NEMA L21-30 for a Main Inlet connector. There are four 20 Amp independent circuit breakers on the front panel, each of which are connected to one of the three phases ( X, Y & Z ) of the main power inlet connector. The X2 & Y2 Phase breakers distribute power to a split T-slot duplex U-ground receptacle located on the rear panel and Y1 & Z1 distribute power to a split T-slot duplex U-ground receptacle located on the rear panel…
|
|
|
SLP-337 The SLP-338 is a 2U high 19" rack mount (220 Volt, 30 Amp, 3�) power distribution bar.
|
|
|
SLP-338 The SLP-338 is a 2U high 19" rack mount (220 Volt, 30 Amp, 3�) power distribution bar. This model has a NEMA L21-30 for a Main Inlet connector. There are six independent 20 amp breakers located on the front panel. Each of the X1 & Y1 breakers distribute power to a T-slot duplex U-ground receptacle located on the rear panel. In addition, the X2 & Y2 breakers distribute power to a split T-slot duplex U-ground receptacle located on the rear panel which is also parallel connected to a split T-slot duplex U-ground convenience receptacle located on the front panel.
|
|
|
SLS 2 The SLS-2 is a speaker cable splitter/combiner patch panel, primarily for installation amplifier racks. Using Neutrik speaker cable jumpers, the amplifier outputs conveniently patch into the front panel. The outputs on the rear panel then combine channels 1 & 2 into a single NL4 connector providing a Bi-amp output marked 1-2. This is repeated for channels A 3-4, B 1-2 and B 3-4.
|
|
|
SLS 4 The SLS-4 is a speaker cable splitter/combiner patch panels for portable and installation amplifier racks. The SLS-4 is essentially an SLS-2 with the connectors placed on the opposite sides or panels of the enclosure. Using Neutrik speaker cable jumpers, the amplifier outputs conveniently patch into the rear panel. The output or front panel then combines channels 1 & 2 into a single NL4 connector providing a Bi-amp output marked 1-2. This is repeated for channels A 3-4, B 1-2 and B 3-4.
|
|
|
SLS 4D The SLS-4 is a speaker cable splitter/combiner patch panels for portable and installation amplifier racks. The SLS-4 is essentially an SLS-2 with the connectors placed on the opposite sides or panels of the enclosure. Using Neutrik speaker cable jumpers, the amplifier outputs conveniently patch into the rear panel. The output or front panel then combines channels 1 & 2 into a single NL4 connector providing a Bi-amp output marked 1-2.
The SLS-4D has a parallel connected NL8 that enables the user to patch a second Stage Box NL8FC cable connection into the same amplifier outputs.
|
|
|
| SLS 6The SLS-6 is a speaker cable splitter/combiner patch panel for portable and installation amplifier racks. The SLS-6 is an SLS-3 with the connectors placed on the opposite sides or panels of the enclosure. The SLS-6 is essentially three Cable Cube DISTRO/MATRIX units in a 2U rack mount panel. Using Neutrik speaker cable jumpers, the amplifier outputs conveniently patch into the rear panel. The output or front panel then combines channels A1 & A2 into a single NL4 connector providing a Bi-amp output marked 1-2. This is repeated for channels A 3-4, B 1-2, B 3-4 C 1-2 & C 3-4.
|
|
|
| SLS 6DThe SLS-6D is a speaker cable splitter/combiner patch panel for portable and installation amplifier racks. The SLS-6D is an SLS-3 with the connectors placed on the opposite sides or panels of the enclosure. The SLS-6 is essentially three Cable Cube DISTRO/MATRIX units in a 2U rack mount panel. Using Neutrik speaker cable jumpers, the amplifier outputs conveniently patch into the rear panel. The output or front panel then combines channels A1 & A2 into a single NL4 connector providing a Bi-amp output marked 1-2. The SLS-6D has a parallel connected NL8.
|
|
|
